Rock Crusher Supplier Manila

1500+Service Persons Waiting for You

According to SBM's business coverage, we have established strong installation engineer teams and divided them into several parts according to the businesses, including building aggregate team, ore processing team and industrial milling team. Each team consists of young, middle-aged, and old engineers, fully satisfying business requirement and fulfilling talent cultivation objective.

At SBM, we adhere to the principle of providing each customer specific design solution. Relying on our sales managers' professional knowledge and our services throughout the life cycle of products, we help our customers out of their difficulties in equipment procurement, operation cost accounting, operation management, and after-sales service obtainment, thus improving their profit-making capability and realizing sustainable development of our business.

100+Online Service Team

Wherever you are, domestically or abroad, you can contact us at any time because SBM has established an online consultation service team consisting of more than 100 persons who provide 365 days×24 hours services for customers.

Service Assurance

Project Detail

Service Life Of Broken And Rolled Walls

The crushing wall and the rolling mortar wall are the main components that work together in the Manila Rock Crusher to crush the material. When the Manila Rock Crusher is in operation, the crushing wall will make trajectory movement, and the distance from the rolling wall is sometimes close to and away from it. The material is repeatedly squeezed by the crushing wall (moving cone) and the rolling wall (fixed cone). Shocked and broken, at this time part of the material will be discharged from the open edge discharge port. In the Manila Rock Crusher, the crushing wall and the rolling mortar wall are the main components that directly contact the material. After using for a period of time, wear will inevitably occur. The service life of the broken wall and the mortar wall is shown in the figure:

In general, the crushing wall and rolling wall of the Manila Rock Crusher can be used for 6 months, but some users have learned that it needs to be replaced after 2-3 months of use. Because its life is affected by many factors, there will be different degrees of wear. When the thickness of the crushing wall and the mortar wall of the Manila Rock Crusher is worn to two-thirds, or it is cracked, the ore discharge opening is enlarged to an extent that it cannot be used. When adjusting, it needs to be replaced.

Replacement Of Crushing Wall And Rolling Wall Of Manila Rock Crusher

When replacing the crushing wall and rolling wall of the Manila Rock Crusher, the wear of the fixed cone, adjusting ring, locking thread, counterweight and counterweight guard must be checked. If the wear is serious, replace it with a new one, and then install the lining board, which can reduce the time for second replacement and disassembly, saving time and effort. After installation of the lining board, it is necessary to check whether the center of the lining board is aligned. Otherwise, the lining board will collide during the running process, resulting in serious wear of the lining board.

Replacement Of The Mortar Wall

The mortar wall can be replaced on site. Unscrew the adjustment screw sleeve installed on the upper frame (note that it rotates counterclockwise), remove the upper chamber hopper assembly, use a lifting device to lift the adjustment screw sleeve, and remove the adjustment screw sleeve plate bolts. The mortar wall is rolled down for replacement. The outer surface is cleaned during assembly, the screw thread surface of the adjustment screw is coated with butter, and it is mounted and fixed in reverse order.

Precautions

U-shaped screws are rolled on the adjusting ring on the adjusting ring, and zinc alloy is injected between the two to make them tightly connected. When newly installing or replacing the rolling wall, the tightening condition should be checked after 6-8 hours of work. And tighten the U-screw again.

Replacement Of Broken Walls

The broken wall can be replaced on site. Lift the main shaft components and place them on a solid support platform. Pay attention not to damage the moving cone and spherical surface. At the same time, block all oil holes with cloth to prevent dust and impurities from entering. Remove the distribution plate, lock nuts, and lock washers in order. , Fusible gasket, welding the two lifting ears on the old board 180 ° apart, the broken wall can be lifted out, the new wall can also be welded on the 180 ° part Ears, then install them in the reverse order of removal, and cut off the two lifting ears when finished.

Precautions

The wall of the Manila Rock Crusher is fixed on the conical body with a conical head. A zinc alloy is cast between the two. The newly installed or newly replaced Manila Rock Crusher’s wall should be checked for tightness after working for 6-8 hours. If it is found loose, it should be tightened immediately.

The crushing wall and rolling wall are important components in the Manila Rock Crusher. During the operation of the Manila Rock Crusher, it should be noted that the materials put into the Manila Rock Crusher must meet the crushing requirements. It is strictly forbidden that the hardness is too high, the moisture is too high Other non-crushing materials enter the crushing cavity, otherwise the crushing wall will fall off and the equipment will stop. At the same time, the feed of the Manila Rock Crusher must be uniform, and the ore must be in the middle of the distribution plate. The material cannot directly interact with the crushing wall and the mortar wall to prevent uneven wear. If you have any other questions, please consult our online customer service directly.

Spare Parts Supply

To deliver spare parts to customer's production sites as fast as possible, SBM has built spare parts warehouses. On receiving customer's call, we take spare parts from the warehouse in the shortest time possible to reduce customer's awaiting time and risk of equipment outage.

Hot Products