Cement Clinker Grinding Process2020-04-22

Summary:Common Faults Of Cement Clinker Grinding Process Equipment Cement Clinker Grinding Process Equipment is a popular grinding equipment in domestic and foreign industrial grinding industry, which plays an important role in stone powder, …

Grinding Equipment Manufacturer

The PC Hammer Mill, MTW, MTM Medium Speed Trapezium Mill, Ball Mill and the LM, LUM Vertical Mill cover all requirements of crude, fine and ultrafine powder production in the industrial milling field. Production of free combination from 0 to 2500 meshes can be realized. No matter which industry you are in, chemistry, energy, construction material or metallurgy field, SBM will always meet all your demands.

Cement Clinker Grinding Process

Spare Parts Supply

SBM has a good many warehouses of spare parts. High-quality spare parts ensure safe and stable operation of equipment. Rapid transport by air removes worry about production interruption loss.

Providing accurate assessment of spare parts' consumption to ensure successful implementation of production plan. Rapid supply of high-quality spare parts to ensure continual operation of production lines so as to prevent loss.

Cement Clinker Grinding Process Detailed introduction

Common Faults Of Cement Clinker Grinding Process Equipment

Cement Clinker Grinding Process Equipment is a popular grinding equipment in domestic and foreign industrial grinding industry, which plays an important role in stone powder, chemical industry and other industrial production. Based on years of experience in Cement Clinker Grinding Process Equipment maintenance, the manufacturer of Cement Clinker Grinding Process Equipment summarizes the faults of Cement Clinker Grinding Process Equipment, hoping to help you.

1. Overheating Of Bearing Temperature

As we all know, the bearing is the core part of the grinding machine, and it belongs to the easily worn part of the grinding machine. It is inevitable that the wear of the bearing is larger than that of the general device.

On the one hand, the bearing temperature is high because the material itself is not resistant to high temperature, but now the Cement Clinker Grinding Process Equipment manufacturers pay great attention to this point. Generally, the material is wear-resistant, hard and high temperature resistant material; it may also be because the bearing lubricating oil is too little, or the lubricating oil should be aged and replaced. After the lubricating oil is used for a long time, the impurities increase, and the lubricating effect on the bearing of the mill will be greatly reduced; or it may be because of the grinding The bearing cover of the pulverizer is too tightly connected with the shaft; in addition, it may be because the bearing seat is uneven and the motor rotor and the pulverizer rotor are not concentric, which makes the bearing unnecessary friction and impact.

In view of the above reasons, the manufacturer of the Cement Clinker Grinding Process Equipment suggests that the manufacturer should check the above conditions one by one, and change the lubricating oil in time; assemble the connection strength of the bearing cover and the bearing; pay attention to the problems of the bearing seat and the concentricity of the rotor to avoid unnecessary impact on the bearing.

2. Too Little Or Too Much Flour From The Pulverizer

As long as the Cement Clinker Grinding Process Equipment production line is fed evenly and appropriately, the powder output is also very uniform and smooth. Once it is found that too little powder is discharged, it may be due to the loose sealing of the powder lock, which causes the problem of the back suction of the pulverizer and the blockage of the air duct; if too much powder is discharged, it is generally due to the insufficient initial layer on the surface of the filter bag of the dust remover or the damage of the filter bag.

In view of the above reasons, we should check whether the installation of the powder locking device and the dust remover is normal, dredge the air duct, replace the parts that cannot work in time, and do a good job in the maintenance of the Cement Clinker Grinding Process Equipment.

3. Frequent Shutdown Of Pulverizer

This Cement Clinker Grinding Process Equipment failure is believed to be deeply understood by the majority of Cement Clinker Grinding Process Equipment users, which may be caused by uneven feeding or too hard material, too much material accumulated in the grinding chamber, and the work of the Cement Clinker Grinding Process Equipment production line is under great pressure; it may also be caused by the tripping of the downstream equipment of the Cement Clinker Grinding Process Equipment production line, resulting in the shutdown of the mill.

In view of the above reasons, the Cement Clinker Grinding Process Equipment manufacturer suggests that the feeding speed of the customers must be well controlled. For the hard materials, the crusher should be used first to crush, and then the grinding work should be carried out. For other equipment shutdown, the reasons should also be checked to ensure the smooth and efficient operation of the Cement Clinker Grinding Process Equipment production line.

Why choose us

For complaints about production line operation from customers, we undertake to complete problem identification and solution offering within 24 hours, and solve the problem within 3/10 days for domestic/foreign customers.

Last:

Inquriy